Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP

Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP
Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP
Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP
Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP
Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP
Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP
Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP
 
Precio$37,000
CódigoADE7763ARSZ
UbicaciónBogota
Stock: 0
SKUSKU0339
Local0B-05-01 No hay comentarios
 
Agotado
Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP


Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP


Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP

Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP ADE7763ARSZ

Ver Hoja Técnica.



Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP

Circuito Integrado Sensor de Potencia electrica 1 Fase 20SSOP ADE7763ARSZ

Ver Hoja Técnica.



Guarde la lista de peticiones

Features Ver Hoja Técnica.

- High accuracy; supports IEC 61036/60687, IEC62053-21, and IEC62053-22
- On-chip digital integrator enables direct interface-to-current sensors with di/dt output
- A PGA in the current channel allows direct interface to shunts and current transformers
- Active and apparent energy, sampled waveform, and current and voltage rms
-Less than 0.1% error in active energy measurement over a dynamic range of 1000 to 1 at 25°C
- Positive-only energy accumulation mode available
- On-chip user programmable threshold for line voltage surge and SAG and PSU supervisory
- Digital calibration for power, phase, and input offset
- On-chip temperature sensor (±3°C typical) SPI®-compatible serial interface
- Pulse output with programmable frequency
- Interrupt request pin (IRQ) and status register
- Reference 2.4 V with external overdrive capability
- Single 5 V supply, low power (25 mW typical)s.

Nota: La tarjeta adaptadora se vende por separado


General Desciption

The ADE77631 features proprietary ADCs and fixed function DSP for high accuracy over large variations in environmental conditions and time. The ADE7763 incorporates two second-order, 16-bit Σ-Δ ADCs, a digital integrator (on Ch1), reference circuitry, a temperature sensor, and all the signal processing required to perform active and apparent energy measurements, line-voltage period measurements, and rms calculation on the voltage and current channels. The selectable on-chip digital integrator provides direct interface to di/dt current sensors such as Rogowski coils, eliminating the need for an external analog integrator and resulting in excellent long-term stability and precise phase matching between the current and the voltage channels.
The ADE7763 provides a serial interface to read data and a pulse output frequency (CF) that is proportional to the active power. Various system calibration features such as channel offset correction, phase calibration, and power calibration ensure high accuracy. The part also detects short duration, low or high voltage variations.
The positive-only accumulation mode gives the option to accumulate energy only when positive power is detected. An internal no-load threshold ensures that the part does not exhibit any creep when there is no load. The zero-crossing output (ZX) produces a pulse that is synchronized to the zero-crossing point of the line voltage. This signal is used internally in the line cycle active and apparent energy accumulation modes, which enables faster calibration.
The interrupt status register indicates the nature of the interrupt, and the interrupt enable register controls which event produces an output on the IRQ pin, an open-drain, active low logic output.

No recommended products at the moment.
No recommended products at the moment.